PowerStart 1000A Car Jump Starter

Introducing the "PowerStart 1000A Car Jump Starter," your reliable companion for those unexpected car battery emergencies. With its high capacity and robust performance, this portable device is designed to jump-start your vehicle with ease.

Key Features:

• Supports QC3.0 fast charging.
• Stable voltage, current, balance charge function.
• Class A cell, safe and explosion protective.
• Upgrade 4 cell and start strongly.
• 1000A Peak current.
• 20000mAh Large Capacity.
• Diesel 5.0L, gasoline 6.0L car can be used.
• Reverse connection protection.
• 4 USB charging.
• Full power can be started 30 times.
• Support 18W phone fast charge.
• Limit temperature -40 ~  80°C.
• Intelligent Protection System.
• The charging head of the product is European Plug.
  
  

Night emergency, Rescue lighting:

• Built-in glare lighting system.
• Double click to enter,red and blue flashes,double click again to exit.
• Long press the middle button for 3 seconds.
• Press again in burst mode.
• After turning on the flashlight,press the switch again to become a flash,the switch is the distress mode.

Note:
The product has just been received, you must first turn on the flashlight to discharge, and then charge the product for more than 4 hours, and then start the car, because the product is empty. This operation can prolong the service life of the product!

1. It is recommended to start the car with three grids or more than 60% of the power supply.

2. Check whether the pile head of the battery is clean. Whether the clamp is stable and does not shake. First clamp the positive and negative poles of the clip to the positive and negative poles of the battery respectively, and wait for 2 to 3 minutes before starting the car. This operation can reduce the load on the power supply

Tips before use
【1】The car cannot be continuously ignited to start the car / or the key is not released, and the next start will be carried out after 30 seconds between each start
【2】The positive and negative poles cannot be reversed. Do not short-circuit the two clips, it will cause an explosion.
【3】Remove the clip within 30 seconds after successfully starting the car. Violation of the above 3 points may cause the [fuse box] of the clip to burn out, please pay attention to the operation method.

 

 

1. Insert the clip into the power start clip,it is recommended ti display more than two battery levels.
2. The red clip (+) is connect to the positive electrode,the black clip(-) is connected to the negative electrode.

 

 

 

 

3.get into the car and start on the car 
4.remove the clip .the start is complete!

Tips :
It is recommended to remove the clip within 30 second.

Note:

• It takes about 3 hours for the product to be fully charged. Turn ON first and then charge the product.
• When starting the car, you need to turn the switch to OFF before starting the car.
  
• Our car power supply has the difference between the peak value 400A and the peak value 600A. The product with a peak value of 400A is 40C, which can start gasoline-powered car with a displacement below 4.0. The doubling of peak 600A is 60C. Can start diesel vehicles with a displacement of less than 6.0 gasoline-powered car and a displacement of less than 2.0. (Except cars with aging engines.)
  
• The product is not used for a long time. It is recommended to charge it once every 3 months.
  
• The product needs to be placed at room temperature, which is beneficial to the service life of the product.

Special precautions for using mobile power:

• When starting the car, insert the blue plug tightly and into place, otherwise the effect will be affected.
• When starting the car, the blue power indicator should be more than 60%, which can prolong the service life of the product.
• If the car cannot start, do not force it to start. Check whether the battery clip is properly clamped and whether the original car battery terminal is rusty and dirty. Continue to start after cleaning.
• In the process of starting, if the vehicle cannot start all the time (1-2 times), do not force to continue starting, and further check whether there are other faults, otherwise, the fuse will be burned and the starting power supply will be damaged.
• when starting the car, the clip port has been used to use air pump and other on-board electrical appliances, the switch needs to be turned OFF.
• Our car power supply uses different styles of 400A and 600A. If your car exceeds the number of products, the power supply will play an automatic power-off protection function when starting the car, plug in the charger and reactivate it to use it normally.
• When the car is fed and there is no electricity at all, clamp the car power clip directly on the positive and negative poles of the car to start. If the car is powered, remove the positive poles, clamp the clip on the ground iron and the negative clip on the negative pole. Can be started.
• When starting the car for the first time, you need to put off the electricity in the product, plug in the charger to charge it, and then start the car.